Kenaz Labs

Why earbuds drain overnight, and how to stop it

Short answer: earbuds you fall asleep with never switch off. They stay connected to the phone, noise cancelling keeps the microphones running, and every time you lie on them they wake up again. On our CMF Buds 2 that cost about 10 % battery per hour, even with nothing playing.

Three things together fixed it: noise cancelling off, the press-and-hold gesture off, and the earbuds disconnected from the phone. With those, the same earbuds used 1–2 % per hour.

Why the earbuds stay on

Most wireless earbuds have no off button. They power down by themselves, and only after they have had no Bluetooth connection for some time. A sleep timer that pauses the music changes none of that: the earbuds are still connected, so they stay awake.

We tested this on a pair of CMF Buds 2 lying on a table:

SituationResult
Connected to the phone for 2 h 49 min, in-ear detection offStill on
Disconnected for 15 minutes, in-ear detection off (tried twice)Still on
Disconnected for 61 minutes, in-ear detection offPowered off
Disconnected for about 62 minutes, in-ear detection onPowered off

So CMF Buds 2 need about an hour without a connection before they power off. Nothing Ear needs about four hours. Other brands have their own rules.

What we measured in bed

All numbers come from the earbuds' own battery reports, on one pair of CMF Buds 2, worn in bed in November 2026. The readings we saw were all multiples of 5 %, so the hourly rates are approximate.

NightWhat happenedBatteryPer hour
2–3 NovThe earbuds reconnected at midnight and stayed connected, with no audio playing.80 % at 00:00, 25 % at 05:39≈ 10 %
4–5 NovDisconnected after the timer. Woken 22 times by being lain on, and disconnected again each time within 2–3 seconds. Noise cancelling or transparency was on for most of the night.70 % at 22:55, 10–15 % at 05:008–9 %
5–6 NovNoise cancelling and press-and-hold turned off when the timer ran out, then disconnected. Woken 17 times.For example 85 % at 23:27, 75–80 % at 02:47≈ 2 %
9–10 NovSame settings. Woken 19 times, and disconnected again each time.70 % at 01:14, 65 % at 05:35≈ 1.2 %

The night of 4–5 November is the interesting one. The earbuds were disconnected almost the whole night and still lost 8–9 % per hour, nearly as much as when they were connected. The longest stretch without a wake-up was 101 minutes, and they lost 15 % in that stretch too, so they had not powered off.

The noise-control mode kept changing between wake-ups: noise cancelling, transparency, off. By default the press-and-hold gesture switches the noise-control mode, and lying on an earbud can trigger it. Noise cancelling and transparency keep the microphones running, and that is the best explanation we have for the drain.

On one other night the earbuds lay untouched beside the pillow after the disconnect, and used almost nothing.

What stops the drain

  1. Turn noise cancelling and transparency off. This made the biggest difference in our nights.
  2. Turn the press-and-hold gesture off, so lying on an earbud does not switch noise cancelling back on. It helps, but it is not watertight: on 9–10 November noise cancelling still came back on at 5 of 19 wake-ups with the gesture off, so it is worth turning it off again whenever the earbuds wake up.
  3. Turn in-ear detection off, so an earbud that is still in your ear does not count as being in use. We have not measured this step on its own.
  4. Disconnect the earbuds from the phone, so they can power themselves off.

On Nothing and CMF earbuds all four are ordinary settings in the Nothing X app, so you can do this by hand: change them when you go to bed and change them back in the morning. The catch is that you have to do it while you are still awake, which means before you have finished listening.

If you are not falling asleep with the earbuds in, the simple answer is the charging case. There they charge instead of draining.

What Natta automates

Natta is our Android sleep timer. It does the four steps for you at the moment the timer runs out, after fading out and pausing the audio. It also handles the two things you cannot do in your sleep:

The full sequence works on Nothing Ear and CMF Buds, and is tested on CMF Buds 2. See which earbuds Natta supports.

Limits of these numbers

If you measure your own earbuds, we would like to hear the result: support@kenazlabs.com.